Port | DUBAI |
Packaging | 1LTR 12 PCS IN CTNS/4LTRS 4 IN A CTN AND 18LTRS |
Lead Time | 3 DAYS |
Ritver Synthetic Alkyd Topcoat Enamel (Standard) is based on a drying oil Alkyd resin,
containing Titanium dioxide and other carefully chosen pigments. It is a product used as general
purpose Topcoat enamel which is very versatile and can withstand wide range of temperatures.
It has good adhesion and exhibits good gloss after drying.
USE
Substrates: plaster, masonry, brickwork, blocks work, wood work and metals.
Area of Use: Interiors and Exteriors.
SPECIFICATIONS
Properties
Finish : Glossy and smooth.
Colour : White + all colors as per the Ritver shade card.
Specific gravity : 1.06 +/- .005
Mixed Solids (% by volume) : 50 2
Diluent : White spirit
Flash point : 38°c
Spread Rate:
While the spread rate is directly dependant on the surface profile and also the type of
undulations it has, as a thumb rule Ritver Synthetic Alkyd Topcoat Enamel (Standard)
would cover 10 – 12 meters per lit.
Drying Time (30° C) : Set to touch: 3 – 4 hours.
: Ready for Recoat: app 16 hours.
Recommended DFT : 1 mist coat followed by a good full coat
App 40 - 50 mic.
SURFACE PREPARATION
A good surface preparation and following the method statement / recommended system
procedure of Ritver is an ideal recommendation for the application of Ritver Synthetic Alkyd
Topcoat Enamel (Standard).
For Plaster, Masonry & Concrete:
Achieve a good and clean surface by removing all contaminants by cleaning & drying. A laitance
free surface should be achieved by good sweep blast or a wire brush. Apply one coat of Ritver
Synthetic Red oxide / Ritver Synthetic Primer for wood, followed by Ritver Synthetic
Undercoat and proceed for Ritver Synthetic Alkyd Topcoat Enamel (Standard) after drying.
Apply one good coat or two nominal coats with a spray or a suitable roller and obtain the desired
coverage.
For wood: Achieve a good and clean surface by removing all contaminants by cleaning & drying.
Wood may be treated with Ritver wood preservative before application.
SYNTHETIC ALKYD TOPCOAT ENAMEL
(STANDARD) Product No. PS3001
This information contained in the data sheet is to the best of our knowledge correct and up to date. Under well-defined conditions. Its accuracy or suitability under the
actual conditions of any independent use is not guaranteed and must be determined by the user. All advice given about this product is given in good faith. Since as we
have no control over conditions of substrate and application, manufacturer and seller cannot accept any liability in connection with the use of the product relative to
coverage, performance, injury, or damage, unless we specify in writing to do so. The information in this data sheet is subject to change without prior notice and it is the
user responsibility to ensure it is current. For further information and advice please contact RITVER Technical Service Department.
Date Revised: 01st Jan 2012 2
TYPICAL PAINT SYSTEM
Apply one coat of Ritver Synthetic Red oxide / or Ritver Synthetic Primer for wood,
followed by Ritver Synthetic Undercoat and proceed after drying.
Apply one good coat or two nominal coats with a spray or a suitable roller and obtain the desired
coverage.
Exclusions for successful application include perpetually wet surfaces and also large cavities on
wood, metal or concrete surfaces.
APPLICATION METHODS
Adequate ventilation is an ideal situation as it helps in drying and the good application itself.
Avoid high humid conditions i..e., >95% when condensation is likely to interfere and also when
the surface temperature is at least 3°c above dew point.
Application: To be done by conventional roller or spray at 2000 – 2500 psi for airless spray or
50 – 60 psi for conventional spray. Nozzle size: 0.015 - 0.018 inches.
One can add 5 - 10% of Ritver General Purpose Thinner for ease of application of
brush/roller/or spray viscosity.
Caution: Over diluting would result in sag and run downs.
Ritver Synthetic Enamel (Standard)
Glossy
Or as per Ritver technical advice
Ritver Synthetic Red Oxide Primer
Ritver Synthetic Undercoat
Ritver Synthetic Enamel (Standard) Glossy
1 coat
1 coat
2 coats
APPLICATION METHODS
STORAGE & SHELF LIFE
Under dry and cool condition, Storage stability can be sound up to 18 months in original sealed
containers.
HANDLING
Disposal: As per the guidance and legislations of the local Authority e.g., by controlled landfill.
In case of doubt, consult local authority. Do not empty into drains, sewers or other water
courses.
Flash Point: Contains mineral spirit and 38°C.
Caution: It is strongly advised not to keep open half used drums as it forms a skin on the top
layer
SYNTHETIC ALKYD TOPCOAT ENAMEL
(STANDARD) Product No. PS3001
This