Port | DUBAI |
Packaging | 1LTR 12 PCS IN CTNS/4LTRS 4 IN A CTN AND 18LTRS |
Lead Time | 3 DAYS |
Ritver Gold Emulsion is an economical grade emulsion (VALUE FOR MONEY RANGE) based
on copolymer with Titanium and other light fast alkali resistant pigments. It gives the surface
a smooth and pleasing effect with good brush ability and recoat ability. It is resistant to algae
and fungus attacks.
USE
Substrates: Concrete, plaster, masonry, gypsum.
Area of Use: Interiors only.
SPECIFICATIONS
Properties
Finish : Smooth & Matt
Colour : White + All shades as per Ritver shade card and custom made.
Specific gravity : 1.5 .02
Solids (%by volume) : 34 1%
Diluent : Sweet Water
Flash point : Not Applicable
Spread Rate :
While the spread rate is directly dependant on the surface profile and also the type of
undulations it has, over spray and also the equipment the painter Ritver Gold Emulsion it
would cover app 8 m2 / liter at 40 microns per coat.
Drying Time (30° C) : Set to touch: 1 – 2 hours.
: Ready for Recoat: app 2 - 3 hours.
Recommended DFT : 1 to 2 coats. App 30 – 40 mic per coat.
SURFACE PREPARATION
A good surface preparation and following the method statement / recommended system
procedure of Ritver is an ideal recommendation for the application of Ritver Gold Emulsion.
For Plaster, Masonry & Concrete:
Achieve a good and clean surface by removing all contaminants and loose particles by
cleaning & drying. A laitance free surface should be achieved by good sweep blast or a wire
brush. Water washing under pressure is recommended.
Apply the Ritver PVA Primer Sealer or Ritver Alkali Resistant Primer and allow drying
as per the data sheet and subject to one more coat for even coverage. Apply Ritver Stucco
Putty evenly and allow drying and following it up with Ritver Gold Emulsion for one or two
coats.
For Old and Painted surfaces:
In case of surfaces which are painted / or aged and is visible dusting, chalking or even friable
ensure that all the loose material is removed by scrapping or metal brush. Apply a good coat
Ritver Fungicidal wash compound and allow drying. Follow this by a regular coat or two
of Ritver PVA Primer Sealer or Ritver Alkali Resistant Primer and continue as in the
above case.
GOLD EMULSION Product No. PW3001
This information contained in the data sheet is to the best of our knowledge correct and up to date. Under well-defined conditions. Its accuracy or suitability
under the actual conditions of any independent use is not guaranteed and must be determined by the user. All advice given about this product is given in good
faith. Since as we have no control over conditions of substrate and application, manufacturer and seller cannot accept any liability in connection with the use of
the product relative to coverage, performance, injury, or damage, unless we specify in writing to do so. The information in this data sheet is subject to change
without prior notice and it is the user responsibility to ensure it is current. For further information and advice please contact RITVER Technical Service
Department.
Date Revised: 01st Jan 2012 2
STORAGE & SHELF LIFE
TYPICAL PAINT SYSTEM
APPLICATION METHODS
Adequate ventilation is an ideal situation as it helps in drying and the good application itself.
Avoid high humid conditions i.e., >95% when condensation is likely to interfere and also
when the surface temperature is at least 3°c above dew point.
1. Dilution: One can add 5 to 10% of sweet water for ease of application depending on
the suitability of application.
2. Brush: It is in ideal recommendation especially to avoid runs and sags due to excess
material.
3. Roller: Apply an even coat spreading uniformly taking care to avoid runs.
4. Airless spray: Use tip size around 0018” to 0020” and pressure around
150. – 175 Kg/cm².
Ritver Gold Emulsion
Recommended system to be applied as per
surface preparation.
Or as per Ritver technical advice
Ritver Primer Sealer
Ritver Stucco Putty
Ritver Gold Emulsion
1 coat
2 coats
2 coats
Under dry and cool condition, storage stability can be sound up to 18 months in original
sealed containers.
HANDLING
Disposal: As per the guidance and legislations of the local Authority e.g. by controlled
landfill. In case of doubt, consult local authority. Do not empty into drains, sewers or other
water courses.
Flash Point: Not applicable
SAFETY PRECAUTION
Avoid contact with the skin and eyes. Wear suitable protective clothing such as overalls,
goggles, dust mask and gloves. Use a barrier cream.
Ensure that there is adequate ventilation in the area where the product is being applied. Do
not breathe vapour or spray.
MSDS is available on request for the safe handling of this product.
FIRST AID
Eyes: In the event of accidental splashes, flush eyes with warm water immediately and
obtain medical advice.
Skin: Wash skin thoroughly with soap and water or approved industrial cleaner. DO NOT USE
solvent or thinners.
Inhalation: Remove to fresh air, loosen collar and keep patient rested.
Ingestion: In case of accidental ingestion DO NOT INDUCE VOMITING. Obtain immediately
medical attention.