SiC Heater High Temperature Heating Elements

Quantity	10 -
Price	$20

MOQ	10 pieces
Port	Shanghai
Packaging	Standard Wooden Case with Sponge and Carton inside
Lead Time	7-30 days

Contact Now

Product Details

Silicon Carbide Heater High Temperature Heating Elements

Sic Heating Elements General Description

Sic Heating Elements is a kind of non-mental high temperature electric heating element.It is made of selected high-purity green silicon carbide as raw material which is made into blank and silicon crystal under high temperature of 2400ºC. It can usually make use for furnance which temperature from 600C-1600ºC. It is widely used in various electric heating element of glass,chemical, electronic material and so on.

Types of Sic Heating Elements:

1. SW (Standard)

SW Silicon Carbides are used in applications ranging in temperature from 600°C up to 1400°C in both air and controlled atmospheres. Although the type of atmosphere used will determine the maximum recommended element temperature. This kind of silicon carbide elements can be mounted either vertically or horizontally.

2. U-TYPE

U shape Silicon Carbide is consists of two silicon carbide rod with same diameter. Each rod has both hot zone and cold end with identical resistance. Two rods are connected by the low resistance SiC. Also the connector could be used as holder according to different requirements.

3. W-TYPE

3-phase elements are available in 2 different types: SGC (Dumbbell), SGD(Standard).

These elements are self-bonded silicon carbide formed by re-crystallization of silicon carbide at high temperature. It consists of three high-purity silicon carbide rods connected at one end by a silicon carbide crossbar. SGC elements are designed for vertical installation in standard float glass bathes and SGD elements for horizontal installation. They can be connected directly on three-phase power supply and is a one-side terminal type which permits drawing out the terminals from the roof of the furnace.

4. Single Spiral Silicon Carbide and Double Spiral Silicon Carbide:

They are made from silicon Carbide powder, and have two shapes: single and double sprial silicon carbide heating element. They are widely used in all kinds of kilns and furnaces.

Recommended surface load and Influences to Surfaces of the Elements in Different Operating TemperatureS

atmosphere	Furnace Temperature(°C)	Surface Load(W/cm2)	The influence on the Rod
Ammonia	1290	3.8	The action on SiC produces methane and destroys the protection film of SiO2
Carbon dioxide	1450	3.1	Corrode SiC
Carbon monoxide	1370	3.8	Absorb carbon powder and influence the protection film of SiO2
Halogen	704	3.8	Corrode SiC and destroy the protection film of SiO2
Hydrogen	1290	3.1	The action on SiC produces methane and destroys the protection film of SiO2
Nitrogen	1370	3.1	The action on SiC produces insulating layer of silicon nitride
Sodium	1310	3.8	Corrode SiC
silicon dioxide	1310	3.8	Corrode SiC
Oxygen	1310	3.8	SiC oxidized
Water-vapor	1090-1370	3.1-3.6	The action on SiC produces hydrate of silicon
Hydrocarbon	1370	3.1	Absorb carbon powder resulted in Hot pollution

Sic Heating Elements Features

Anti-corrosion,

Long service life,

Little deformation,

Easy installation and maintenance.

Excellent specific rate of heat zone resistance and cold end resistance,

Avoiding over-temperature of cold ends to damage the furnace body.

Saving energy

Notice for using and installing:

1. Heater should be protected against damp during storing or installing to ensure the performance of the heater.

2. In order to be sure of well-distributed lod of each and groups, heater should be divided before assembling. The tolerance of the resistance of each one cannot exceed by 10% each other.

3. Heater is hard and brittle, please be careful when assembling and maintaining so as to avoid damage.

4. When operating the electric furnace at the beginning, the voltage should be increased slowly and cannot be fully loaded at once. Otherwise the larger current will be resulted in the damage of heater.