Bausch & Lomb Stellaris PC

Product Details

Bausch & Lomb Stellaris PC  

Bausch & Lomb Stellaris PC Features

The Bausch & Lomb Stellaris PC microsurgical system provides a high-performance experience in vitreoretinal and cataract eye surgeries. This system enables surgeons to perform different ophthalmic procedures while saving time, space, and money for the surgeons, and the patients. The Stellaris PC system has light-weight, ultra high-speed vitrectomy probes for conventional and transconjunctival vitrectomy.

    Dual light source with surgeon-selected color filters.
    Optimal platform for the smallest incisions for both retinal and cataract surgeries.
    Capable of 1.8 mm MICS phacoemulsification.
    Easily upgraded to take advantage of future technology evolutions.
    19” 5:4 aspect ratio color touch screen display.
    System can be set for either gravity infusion or infusion using pressurized air.

Bausch & Lomb Stellaris PC Specifications

Dimensions

    Height: 48 in (122 cm)
    Width: 18 in (45.7 cm)
    Depth: 18 in (45.7 cm)
    Weight: 230 lbs (114 kg)

Display

    Type: Flat Panel, TFT LCD Full Color
    Size: 19” (48.2 cm) Diagonal
    Pixels: 1280 x 1024
    Tilt: +15° up and -10° down
    Swivel: ±90°

Aspiration

    General: Provides Cassette Full, Near-Full and Continuous Fluid Level Sensing. Programmable vacuum response curves.
    Modes of Operation: Linear control of vacuum. Fixed, On/Off control of vacuum. Dual Linear Modes: Pitch or Yaw.
    Operating Parameters: I/A mode: 0 mmHg to 600 mmHg; Phaco: 10 mmHg to 600 mmHg; Vitrectomy: 0 mmHg to 600 mmHg; Extrude: 0 mmHg to 600 mmHg; Vacuum Control: 1 mmHg increments

Irrigation

    Gravity feed from I/V bottle with pinch valve On/Off control via footpedal

Reflux

    Control: Gravity feed from I/V bottle; Modes: Continuous, Pulsed; Activated via the Foot Control

Vitrectomy

    Linear Cut Rate Mode Operating Parameters: Range: 30 to 5000 cuts per minute in 1 cut per minute increments; Control: Linear control of cut rate via the footpedal
    Fixed Cut Rate Mode Operating Parameters: Range: 30 to 5000 cuts per minute in 1 cut per minute increments; Cut rate is derated no more than 20% above 3000 feet (915 meters) altitude; Control: On/Off control of cut via the footpedal

Ultrasound Functions

    Programming Levels 1,2,3
        Continuous ultrasound
        Pulsed ultrasound
        Fixed pulse ultrasound
        Single burst ultrasound
        Multiple burst ultrasound
    Programming Level 3 only
        Dual Linear Ultrasound
        Linear Power, Linear Pulse ultrasound
        Linear Power, Linear Duty Cycle ultrasound
        Dual Linear Multiple Burst ultrasound
        Variable Power Multiple Burst ultrasound
        Variable Power Linear Burst ultrasound

Viscous Fluid Controls

    Injection Mode Pressure: 70 psi (482.6 kPa, 4.8 bar)
    Extraction Mode Vacuum: Between 5 to 600 mmHg in 10 mmHg increments

Fluid Air Exchange

    Output: 0.1 micron hydrophobic filtered air
    Pressure: 150 mmHg maximum air pressure
    Flow Rate: Up to 4.8 standard cubic feet per hour (2.25 L/min)
    Safety: System includes pneumatic shut-off valve in case of power loss

Illumination

    Modes of Operation: Independent Illumination and control of either port
    Lamp Type: Xenon and Xenon-Mercury
    Output: Light output from a single port is minimum 25 lumens using standard 20g probe.
    Safety Filter: Both ports incorporate permanent filtration to reduce ultraviolet, violet, deep red and infrared light
    Control: 0-100% control range, 1% resolution
    Color Filtration: None, Green, Yellow, Amber (only available on Port 1 when a xenon lamp is installed)