Tenon Biometric RF semiconductor Fingerprint Lock

Product Details

The shell is made of zinc alloy

Use of large industrial machines, casting and molding, super anti - collision, strong safety

Surface using nano coating wire drawing process, touch no mark, always bright as new

Comparison for three generations of fingerprint head

1: Through the light refraction and reflection principle to identify the fingerprint, the identification rate is low and can not eliminate the false fingerprint(optical fingerprint)

2. Semiconductor fingerprint head: USES thermal imaging principle, electronic measurement to capture fingerprints, very fragile, easy to scratch, short life.

3. The sensor emits a trace of radio frequency signal and penetrates the epidermis of the finger to detect the grain of the inner layer, so as to obtain the best fingerprint image, which can be used for accurate living creature identification, anti-scratch and long service life.

RF FINGERPRINT HEAD ADVANTAGES

Strong anti-counterfeiting: 0.1 second instantaneous identification of dermal fingerprints to prevent false fingerprints; Strong self-learning function: learn according to the different finger pressing area and strength, and integrate the newly learned fingerprint features into the existing fingerprint template, the more useful it is; Strong adaptability: dry fingers, wet fingers, light texture fingers, peeling fingers can unlock without hindrance; Strong durability: thick coating on the surface of the sensor ensures 10 million presses; The industry's unique anti-scratch algorithm: when the sensor surface is scratched by hard objects, leaving obvious scratches, it will automatically remove the scratches in the fingerprint image, to ensure continued use

ANTI-PEEP PASSWORD DESIGN

In the real password can be arbitrary input phantom password before and after the longest 18 effectively prevent peeping

Intelligent dormancy is effective against cracking

The system will automatically sleep for 3 minutes after 5 consecutive validation errors of swiping card/password to prevent cracking

Security and reliable, the second core of defence

High electronic anti-theft lock body; Dual core dual system, no fear of small black box cracking; front and back panel are binding with encryption communication, one-to-one matching authentication; Multi-mcu circuit design, a variety of open doors work independently, non-interference.

INTRODUCTION OF CLASS C LOCK CORE

It adopts the structure of 45 degree special-shaped double connecting beads combined with middle bead technology + embedded transverse grid technology + double-row spring technology + double-row curved slot lock cylinder

The core selling point of high configuration electronic lock body

l Durability test ≥ 200,000 times: 20 times per day for up to 27 years

l Transassembly structure, left and right inside and outside can be freely commutating

l Shockproof and loose-proof structure technology: glue will be applied to each screw to prevent long-term shedding from affecting the service life of the lock body

l Quick escape function: spring bolt and lock linkage can open the door quickly in case of emergency

l Internal clutch motor structure design: anti-theft and anti-pry

l With national fire and theft authentication: prevent fire source from spreading inside the lock body, affecting the unlock

S6068T Fully automatic core lock body

Automatically lock the door;

If the square tongue does not pop out, an alarm will be given.

The inclined tongue direction of the lock body can be replaced by removing screws on the liner plate to distinguish between inside and outside;

The gap of the door shall not be greater than 1-7mm;

liner and gusset plate can be customized, not with the heaven and earth hook;

High speed hollow cup motor Test life 20W

From top to the bottom there are 3 tongue, ss wind positioning spring bolt, ss square spring bolt, ss induction spring bolt respectively (Press down 1mm to trigger the motor)

Multi MCU circuit design

TENON creates the overall solution for the security of intelligent lock, configuring multi-system connection operation software with independent intellectual property rights, m-Link operating system.

Electronic identification and control + mechanical linkage system = fingerprint lock

Dual core dual system, no fear of small black box

Low power consumption, low power operation

MCU (micro control unit) circuit design, the fingerprint/password/card lock mode to work independently, not influence each other, greatly increased risk resistance, ability to resist breaking to achieve low power operation, low power consumption for a whole year without changing the battery

OLED DISPALY SCREEN

1. Display: OLED is a self-luminous material, which does not need backlight plate. It has wide viewing Angle, image uniform quality, fast response speed, stable image and high brightness.

2. Working conditions: low drive voltage and low energy consumption.

3. Wide adaptability: OLED is a solid-state, non-vacuum device with anti-vibration and low temperature resistance (-40℃).

Single point capacitive touch button

High strength capacitive sensing touch screen (5 a grade explosion-proof glass, broken can also be used), high precision, strong capability of anti-scratch

capacitive sensing touch keys can penetrate the insulation shell more than 8 mm (glass, plastic, etc.), can be accurate to detect finger touch effectively, ensure the product sensitivity, stability, and have waterproof ability, can be super adaptability to the temperature range, which can effectively use more than 15 years.

China's largest manufacturer of fingerprint locks, the product looks beautiful, exquisite workmanship. It is an inevitable trend that the intelligent lock represented by fingerprint lock replaces the traditional mechanical lock